Beckhoff EL7037 User Manual Page 177
- Page / 227
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Configuration by means of the TwinCAT System Manager
Index 1C33 SM input parameter (part 1)
Index Name Meaning Data type Flags Default value
1C33:0 SM input parame-
ter
Synchronization parameters for the inputs UINT8 RO 0x20 (32
dec
)
1C33:01 Sync mode Current synchronization mode:
• 0: Free Run
• 1: Synchronous with SM 3 event (no outputs
available)
• 2: DC - Synchronous with SYNC0 Event
• 3: DC - Synchronous with SYNC1 Event
• 34: Synchronous with SM 2 event (outputs
available)
UINT16 RW 0x0022 (34
dec
)
1C33:02 Cycle time
as 1C32:02 [}176]
UINT32 RW 0x000F4240
(1000000
dec
)
1C33:03 Shift time Time between SYNC0 event and reading of the inputs (in
ns, only DC mode)
UINT32 RO 0x00000000 (0
dec
)
1C33:04 Sync modes sup-
ported
Supported synchronization modes:
• Bit 0: free run is supported
• Bit 1: synchronous with SM 2 event is supported
(outputs available)
• Bit 1: synchronous with SM 3 event is supported
(no outputs available)
• Bit 2-3 = 01: DC mode is supported
• Bit 4-5 = 01: input shift through local event
(outputs available)
• Bit 4-5 = 10: input shift with SYNC1 event (no
outputs available)
• Bit 14 = 1: dynamic times (measurement through
writing of 1C32:08 [}176] or 1C33:08 [}177])
UINT16 RO 0x0C07 (3079
dec
)
1C33:05 Minimum cycle
time
as 1C32:05 [}176]
UINT32 RO 0x0003D090
(250000
dec
)
1C33:06 Calc and copy
time
Time between reading of the inputs and availability of the
inputs for the master (in ns, only DC mode)
UINT32 RO 0x00000000 (0
dec
)
1C33:07 Minimum delay
time
UINT32 RO 0x00000000 (0
dec
)
Index 1C33 SM input parameter (part 2)
Index Name Meaning Data type Flags Default value
1C33:08 Command
as 1C32:08 [}176]
UINT16 RW 0x0000 (0
dec
)
1C33:09 Maximum delay
time
Time between SYNC1 event and reading of the inputs (in
ns, only DC mode)
UINT32 RO 0x00000000 (0
dec
)
1C33:0B SM event missed
counter
as 1C32:11 [}176]
UINT16 RO 0x0000 (0
dec
)
1C33:0C Cycle exceeded
counter
as 1C32:12 [}176]
UINT16 RO 0x0000 (0
dec
)
1C33:0D Shift too short
counter
as 1C32:13 [}176]
UINT16 RO 0x0000 (0
dec
)
1C33:14 Frame repeat time UINT32 RW 0x00000000 (0
dec
)
1C33:20 Sync error
as 1C32:32 [}176]
BOOLEAN RO 0x00 (0
dec
)
Index F000 Modular device profile
Index Name Meaning Data type Flags Default value
F000:0 Modular device
profile
General information for the modular device profile UINT8 RO 0x02 (2
dec
)
F000:01 Module index dis-
tance
Index spacing of the objects of the individual channels UINT16 RO 0x0010 (16
dec
)
F000:02 Maximum number
of modules
Number of channels UINT16 RO 0x0003 (3
dec
)
EL70x7 177Version 1.0
- Table of contents 3
- 1 Foreword 5
- 1.2 Safety instructions 6
- 1.3 Documentation issue staus 7
- Designation 8
- Identification number 8
- Unique serial number/ID 9
- Examples of markings: 9
- Foreword 11
- EL70x7 11Version 1.0 11
- 2 Product overview 12
- Configuration instructions 13
- Application example 13
- 2.1.2 EL7037 - Technical data 14
- 2.2 EL7047 15
- 2.2.2 EL7047 - Technical data 17
- 2.3 Technology 18
- Stepper motor parameters 19
- • Mechanical system 19
- • Number of phases 19
- • Torque 19
- • Cogging torque 20
- • Mass moment of inertia 20
- • Resonance 20
- 2.3.2 Standard mode 22
- 2.3.3 Field-oriented control 23
- Control structure 24
- Motor dependency 24
- 2.3.4 Sensorless operation 25
- 2.4 Start-up 26
- 3 Basics communication 27
- Multiplier 29
- 3.4 EtherCAT State Machine 30
- Pre-Operational (Pre-Op) 31
- Safe-Operational (Safe-Op) 31
- Operational (Op) 31
- 3.5 CoE Interface 32
- Data management 33
- Online/offline list 34
- Channel-based order 35
- 3.6 Distributed Clock 37
- 4 Installation 38
- Disassembly 39
- PE power contact 39
- Possible damage of the device 40
- Risk of electric shock! 40
- 4.2 Connection system 41
- Wiring HD Terminals 42
- ESxxxx / KSxxxx 43
- Shielding 44
- 4.3 Installation position 45
- 4.5 Shielding concept 47
- 4.6 EL7037 48
- EL7037-0000 49
- Terminal points 50
- Connection types 51
- Bipolar motors 51
- Installation 52
- EL70x752 Version 1.0 52
- 4.7 EL7047 53
- LEDs (left prism) 54
- LEDs (right prism) 54
- Unipolar motors 57
- Connecting an encoder (24 V) 57
- 5 Commissioning 58
- EL70x760 Version 1.0 60
- IP address of the port used 61
- Device differentiation 62
- Online description 62
- Faulty ESI file 64
- EL70x7 65Version 1.0 65
- Creating the EtherCAT device 66
- Defining EtherCAT slaves 68
- EL70x7 71Version 1.0 71
- Selecting the Ethernet port 74
- Online scan functionality 74
- Troubleshooting 77
- Change to compatible device 80
- Change to Alternative Type 80
- „General“ tab 83
- „EtherCAT“ tab 83
- “Process Data” tab 84
- Sync Manager 85
- PDO list 85
- PDO Content 85
- Download 86
- PDO Configuration 86
- „Startup“ tab 86
- “CoE – Online” tab 87
- „Online“ tab 89
- DLL Status 89
- EL70x792 Version 1.0 92
- CoE Parameter Directory 94
- EtherCAT System Documentation 95
- Standard setting 96
- Manual Control 97
- Note regarding E-Bus current 98
- 5.3.1 Process data 99
- PDO Assignment 100
- Predefined PDO Assignment 103
- Adding an axis automatically 105
- Adding an axis manually 105
- Commissioning 108
- EL70x7108 Version 1.0 108
- The motor may overheat! 109
- Base frequency selection 110
- CoE "Feedback type" 111
- Dead time compensation 113
- Scaling factor 113
- Position lag monitoring 114
- factors 115
- Dead band for position errors 116
- Setting the acceleration time 116
- 5.3.5 Application example 117
- 5.4 Operating modes 123
- 5.4.2 Velocity direct 125
- Step by Step 126
- 5.4.3 Position controller 128
- 5.4.4 Extended Velocity mode 131
- 5.4.5 Extended Position mode 134
- 5.4.6 Velocity sensorless 137
- Parameter set 140
- POS Settings 141
- Velocity min.: 141
- Velocity max.: 141
- Acceleration pos.: 141
- Acceleration neg.: 141
- Target overrun: 144
- StartUp: 145
- Start positioning: 145
- Evaluate status: 145
- Error handling: 145
- Start types 145
- ABSOLUTE: 146
- RELATIVE: 147
- ENDLESS_PLUS / ENDLESS_MINUS: 147
- ADDITIVE: 147
- Example: 150
- 6.1 EL7037 155
- Configuration data 156
- Index 8000 ENC Settings Ch.1 156
- EL70x7 157Version 1.0 157
- EL70x7158 Version 1.0 158
- Index 8020 POS Settings Ch.1 159
- Index 8021 POS Features Ch.1 160
- Command object 160
- Index FB00 STM Command 160
- Input data 161
- Index 6000 ENC Inputs Ch.1 161
- Index 6010 STM Inputs Ch.1 161
- Index 6020 POS Inputs Ch.1 162
- Output data 162
- Index 7000 ENC Outputs Ch.1 162
- Index 7010 STM Outputs Ch.1 162
- Index 9010 STM Info data Ch.1 163
- Index 9020 POS Info data Ch.1 164
- Index A010 STM Diag data Ch.1 164
- EL70x7 165Version 1.0 165
- EL70x7 167Version 1.0 167
- EL70x7168 Version 1.0 168
- EL70x7 169Version 1.0 169
- EL70x7170 Version 1.0 170
- EL70x7 171Version 1.0 171
- EL70x7172 Version 1.0 172
- EL70x7 173Version 1.0 173
- EL70x7174 Version 1.0 174
- Index 1C00Sync manager type 175
- Index 1C12 RxPDO assign 175
- Index 1C13 TxPDO assign 175
- EL70x7176 Version 1.0 176
- EL70x7 177Version 1.0 177
- Index F008 Code word 178
- 6.2 EL7047 179
- EL70x7 181Version 1.0 181
- EL70x7182 Version 1.0 182
- EL70x7 189Version 1.0 189
- EL70x7 191Version 1.0 191
- EL70x7192 Version 1.0 192
- EL70x7 193Version 1.0 193
- EL70x7194 Version 1.0 194
- EL70x7 195Version 1.0 195
- EL70x7196 Version 1.0 196
- EL70x7 197Version 1.0 197
- Index 1C00 Sync manager type 199
- EL70x7200 Version 1.0 200
- EL70x7 201Version 1.0 201
- 7 Error correction 203
- Support for commissioning 204
- Interpretation 205
- Structure of the Text ID 205
- General Text IDs 205
- 8 Appendix 208
- 8.2 EtherCAT AL Status Codes 210
- 8.3 Firmware EL/ES/EM/EPxxxx 210
- Update of XML/ESI description 211
- CoE Online and Offline CoE 214
- CoE directory 214
- FPGA firmware *.rbf 215
- Updating an EtherCAT device 217
- Appendix 218
- Fig.190: Select dialog FPGA 218
- EL70x7218 Version 1.0 218
- Risk of damage to the device! 219
- 8.4 Firmware compatibility 220
- Alternative restore value 221
- 8.6 Support and Service 222
- Table of figures 223
Related products and manuals for Equipment Beckhoff EL7037
Equipment Beckhoff ET1200 User Manual
(70 pages)
(70 pages)
Equipment Beckhoff ET1100 User Manual
(119 pages)
(119 pages)
Equipment Beckhoff ET2000 User Manual
(23 pages)
(23 pages)
Equipment Beckhoff ET2000 User Manual
(23 pages)
(23 pages)
Equipment Beckhoff PHY User Manual
(12 pages)
(12 pages)
Equipment Beckhoff FB1111-014x User Manual
(31 pages)
(31 pages)
Equipment Beckhoff ET1100 User Manual
(52 pages)
(52 pages)
Equipment Beckhoff EL9800 User Manual
(36 pages)
(36 pages)
Equipment Beckhoff EP-xxxx-xxxx User Manual
(19 pages)
(19 pages)
Equipment Beckhoff EP-xxxx-xxxx User Manual
(19 pages)
(19 pages)
Equipment Beckhoff EP-xxxx-xxxx User Manual
(19 pages)
(19 pages)
Equipment Beckhoff ET9300 User Manual
(97 pages)
(97 pages)
© 2020, manymanuals.com. All rights reserved. | 0.609 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals