Beckhoff EL7037 User Manual Page 205
- Page / 227
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Error correction
Interpretation
Structure of the Text ID
The structure of the MessageID is not subject to any standardisation and can be supplier-specifically
defined. In the case of Beckhoff EtherCAT devices (EL, EP) it usually reads according to xyzz:
x y zz
0: Systeminfo
1: Info
4: Warning
8: Error
1: General
2: Communication
3: Encoder
4: Drive
5: Inputs
Error number
Example: Message 0x4413 --> Drive Warning Number 0x13
General Text IDs
Specific Text IDs should be specified in the device documentation.
Text ID Type Place Text (English
only)
Cause
0x0001 Informatio
n
System No error No error
0x0002 Informatio
n
System Communication
established
Communication established
0x0003 Informatio
n
System Initialisation: 0x%X,
0x%X, 0x%X
General information; parameters depend on
event. See device documentation for
interpretation.
0x1000 Informatio
n
System Information: 0x%X,
0x%X, 0x%X
General information; parameters depend on
event. See device documentation for
interpretation.
0x1100 Informatio
n
General Detection of the mode of operation ended
0x1135 Informatio
n
General Cycle time OK
0x1201 Informatio
n
Communicatio
n
Communication re-
established
Communication to the field side restored
This message appears, for example, if the
voltage was removed from the power
contacts and re-applied during operation
0x1300 Informatio
n
Encoder Position set - StartInputhandler
0x1400 Informatio
n
Drive Drive is calibrated
0x4000 Warning Warning: 0x%X, 0x
%X, 0x%X
General warning; parameters depend on
event. See device documentation for
interpretation.
0x4101 Warning General Terminal-
Overtemperature
Overtemperature. The internal temperature
of the terminal exceeds the parameterised
warning threshold
0x4300 Warning Encoder Sub-increments deactivated (despite
activated configuration)
0x4301 Warning Encoder Encoder-Warning General encoder error
0x4400 Warning Drive Drive is not calibrated
0x4401 Warning Drive Start type is not supported
0x4402 Warning Drive Command rejected
0x4405 Warning Drive Modulo sub-type invalid
EL70x7 205Version 1.0
- Table of contents 3
- 1 Foreword 5
- 1.2 Safety instructions 6
- 1.3 Documentation issue staus 7
- Designation 8
- Identification number 8
- Unique serial number/ID 9
- Examples of markings: 9
- Foreword 11
- EL70x7 11Version 1.0 11
- 2 Product overview 12
- Configuration instructions 13
- Application example 13
- 2.1.2 EL7037 - Technical data 14
- 2.2 EL7047 15
- 2.2.2 EL7047 - Technical data 17
- 2.3 Technology 18
- Stepper motor parameters 19
- • Mechanical system 19
- • Number of phases 19
- • Torque 19
- • Cogging torque 20
- • Mass moment of inertia 20
- • Resonance 20
- 2.3.2 Standard mode 22
- 2.3.3 Field-oriented control 23
- Control structure 24
- Motor dependency 24
- 2.3.4 Sensorless operation 25
- 2.4 Start-up 26
- 3 Basics communication 27
- Multiplier 29
- 3.4 EtherCAT State Machine 30
- Pre-Operational (Pre-Op) 31
- Safe-Operational (Safe-Op) 31
- Operational (Op) 31
- 3.5 CoE Interface 32
- Data management 33
- Online/offline list 34
- Channel-based order 35
- 3.6 Distributed Clock 37
- 4 Installation 38
- Disassembly 39
- PE power contact 39
- Possible damage of the device 40
- Risk of electric shock! 40
- 4.2 Connection system 41
- Wiring HD Terminals 42
- ESxxxx / KSxxxx 43
- Shielding 44
- 4.3 Installation position 45
- 4.5 Shielding concept 47
- 4.6 EL7037 48
- EL7037-0000 49
- Terminal points 50
- Connection types 51
- Bipolar motors 51
- Installation 52
- EL70x752 Version 1.0 52
- 4.7 EL7047 53
- LEDs (left prism) 54
- LEDs (right prism) 54
- Unipolar motors 57
- Connecting an encoder (24 V) 57
- 5 Commissioning 58
- EL70x760 Version 1.0 60
- IP address of the port used 61
- Device differentiation 62
- Online description 62
- Faulty ESI file 64
- EL70x7 65Version 1.0 65
- Creating the EtherCAT device 66
- Defining EtherCAT slaves 68
- EL70x7 71Version 1.0 71
- Selecting the Ethernet port 74
- Online scan functionality 74
- Troubleshooting 77
- Change to compatible device 80
- Change to Alternative Type 80
- „General“ tab 83
- „EtherCAT“ tab 83
- “Process Data” tab 84
- Sync Manager 85
- PDO list 85
- PDO Content 85
- Download 86
- PDO Configuration 86
- „Startup“ tab 86
- “CoE – Online” tab 87
- „Online“ tab 89
- DLL Status 89
- EL70x792 Version 1.0 92
- CoE Parameter Directory 94
- EtherCAT System Documentation 95
- Standard setting 96
- Manual Control 97
- Note regarding E-Bus current 98
- 5.3.1 Process data 99
- PDO Assignment 100
- Predefined PDO Assignment 103
- Adding an axis automatically 105
- Adding an axis manually 105
- Commissioning 108
- EL70x7108 Version 1.0 108
- The motor may overheat! 109
- Base frequency selection 110
- CoE "Feedback type" 111
- Dead time compensation 113
- Scaling factor 113
- Position lag monitoring 114
- factors 115
- Dead band for position errors 116
- Setting the acceleration time 116
- 5.3.5 Application example 117
- 5.4 Operating modes 123
- 5.4.2 Velocity direct 125
- Step by Step 126
- 5.4.3 Position controller 128
- 5.4.4 Extended Velocity mode 131
- 5.4.5 Extended Position mode 134
- 5.4.6 Velocity sensorless 137
- Parameter set 140
- POS Settings 141
- Velocity min.: 141
- Velocity max.: 141
- Acceleration pos.: 141
- Acceleration neg.: 141
- Target overrun: 144
- StartUp: 145
- Start positioning: 145
- Evaluate status: 145
- Error handling: 145
- Start types 145
- ABSOLUTE: 146
- RELATIVE: 147
- ENDLESS_PLUS / ENDLESS_MINUS: 147
- ADDITIVE: 147
- Example: 150
- 6.1 EL7037 155
- Configuration data 156
- Index 8000 ENC Settings Ch.1 156
- EL70x7 157Version 1.0 157
- EL70x7158 Version 1.0 158
- Index 8020 POS Settings Ch.1 159
- Index 8021 POS Features Ch.1 160
- Command object 160
- Index FB00 STM Command 160
- Input data 161
- Index 6000 ENC Inputs Ch.1 161
- Index 6010 STM Inputs Ch.1 161
- Index 6020 POS Inputs Ch.1 162
- Output data 162
- Index 7000 ENC Outputs Ch.1 162
- Index 7010 STM Outputs Ch.1 162
- Index 9010 STM Info data Ch.1 163
- Index 9020 POS Info data Ch.1 164
- Index A010 STM Diag data Ch.1 164
- EL70x7 165Version 1.0 165
- EL70x7 167Version 1.0 167
- EL70x7168 Version 1.0 168
- EL70x7 169Version 1.0 169
- EL70x7170 Version 1.0 170
- EL70x7 171Version 1.0 171
- EL70x7172 Version 1.0 172
- EL70x7 173Version 1.0 173
- EL70x7174 Version 1.0 174
- Index 1C00Sync manager type 175
- Index 1C12 RxPDO assign 175
- Index 1C13 TxPDO assign 175
- EL70x7176 Version 1.0 176
- EL70x7 177Version 1.0 177
- Index F008 Code word 178
- 6.2 EL7047 179
- EL70x7 181Version 1.0 181
- EL70x7182 Version 1.0 182
- EL70x7 189Version 1.0 189
- EL70x7 191Version 1.0 191
- EL70x7192 Version 1.0 192
- EL70x7 193Version 1.0 193
- EL70x7194 Version 1.0 194
- EL70x7 195Version 1.0 195
- EL70x7196 Version 1.0 196
- EL70x7 197Version 1.0 197
- Index 1C00 Sync manager type 199
- EL70x7200 Version 1.0 200
- EL70x7 201Version 1.0 201
- 7 Error correction 203
- Support for commissioning 204
- Interpretation 205
- Structure of the Text ID 205
- General Text IDs 205
- 8 Appendix 208
- 8.2 EtherCAT AL Status Codes 210
- 8.3 Firmware EL/ES/EM/EPxxxx 210
- Update of XML/ESI description 211
- CoE Online and Offline CoE 214
- CoE directory 214
- FPGA firmware *.rbf 215
- Updating an EtherCAT device 217
- Appendix 218
- Fig.190: Select dialog FPGA 218
- EL70x7218 Version 1.0 218
- Risk of damage to the device! 219
- 8.4 Firmware compatibility 220
- Alternative restore value 221
- 8.6 Support and Service 222
- Table of figures 223
Related products and manuals for Equipment Beckhoff EL7037
Equipment Beckhoff ET1200 User Manual
(70 pages)
(70 pages)
Equipment Beckhoff ET1100 User Manual
(119 pages)
(119 pages)
Equipment Beckhoff ET2000 User Manual
(23 pages)
(23 pages)
Equipment Beckhoff ET2000 User Manual
(23 pages)
(23 pages)
Equipment Beckhoff PHY User Manual
(12 pages)
(12 pages)
Equipment Beckhoff FB1111-014x User Manual
(31 pages)
(31 pages)
Equipment Beckhoff ET1100 User Manual
(52 pages)
(52 pages)
Equipment Beckhoff EL9800 User Manual
(36 pages)
(36 pages)
Equipment Beckhoff EP-xxxx-xxxx User Manual
(19 pages)
(19 pages)
Equipment Beckhoff EP-xxxx-xxxx User Manual
(19 pages)
(19 pages)
Equipment Beckhoff EP-xxxx-xxxx User Manual
(19 pages)
(19 pages)
Equipment Beckhoff ET9300 User Manual
(97 pages)
(97 pages)
© 2020, manymanuals.com. All rights reserved. | 0.660 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals